Switch to Minicore & enable reset toggle on upload

Devices/Control/Firmware/enableReset.py

@@ -0,0 +1,6 @@
+import serial
+import time
+ser = serial.Serial("COM5")
+ser.write(b'r')
+ser.close()
+time.sleep(1)

Devices/Control/Firmware/platformio.ini

@@ -1,16 +1,76 @@
-; PlatformIO Project Configuration File
+[platformio]
-;
+default_envs = Upload_UART ; Default build target
-;   Build options: build flags, source filter
-;   Upload options: custom upload port, speed and extra flags
-;   Library options: dependencies, extra library storages
-;   Advanced options: extra scripting
-;
-; Please visit documentation for the other options and examples
-; https://docs.platformio.org/page/projectconf.html
 
-[env:control]
+
+; Common settings for all environments
+[env]
 platform = atmelavr
-board = nanoatmega328
 framework = arduino
-upload_port = COM6
+
-monitor_port = COM6
+; TARGET SETTINGS
+; Chip in use
+board = ATmega328P
+; Clock frequency in [Hz]
+board_build.f_cpu = 16000000L
+
+; BUILD OPTIONS
+; Comment out to enable LTO (this line unflags it)
+build_unflags = -flto
+; Extra build flags
+build_flags = 
+
+; SERIAL MONITOR OPTIONS
+; Serial monitor port defined in the Upload_UART environment
+monitor_port = ${env:Upload_UART.upload_port}
+; Serial monitor baud rate
+monitor_speed = 9600
+
+
+; Run the following command to upload with this environment
+; pio run -e Upload_UART -t upload
+[env:Upload_UART]
+;  Serial bootloader protocol
+upload_protocol = custom
+; Serial upload port
+upload_port = COM5
+; Get upload baud rate defined in the fuses_bootloader environment
+board_upload.speed = ${env:fuses_bootloader.board_bootloader.speed}
+upload_flags =
+  -C$PROJECT_PACKAGES_DIR/tool-avrdude/avrdude.conf
+  -p$BOARD_MCU
+  -P${env:Upload_UART.upload_port}
+  -carduino
+  -v
+  -V
+  -D 
+upload_command = python enableReset.py && avrdude $UPLOAD_FLAGS -U flash:w:$SOURCE:i
+
+; Run the following command to upload with this environment
+; pio run -e Upload_ISP -t upload
+[env:Upload_ISP]
+; Custom upload procedure
+upload_protocol = custom
+; Avrdude upload flags
+upload_flags =
+  -C$PROJECT_PACKAGES_DIR/tool-avrdude/avrdude.conf
+  -p$BOARD_MCU
+  -PUSB
+  -cusbasp
+; Avrdude upload command
+upload_command = avrdude $UPLOAD_FLAGS -U flash:w:$SOURCE:i
+
+
+; Run the following command to set fuses
+; pio run -e fuses_bootloader -t fuses
+; Run the following command to set fuses + burn bootloader
+; pio run -e fuses_bootloader -t bootloader
+[env:fuses_bootloader]
+board_hardware.oscillator = external ; Oscillator type
+board_hardware.uart = uart0          ; Set UART to use for serial upload
+board_bootloader.speed = 115200      ; Set bootloader baud rate
+board_hardware.bod = 2.7v            ; Set brown-out detection
+board_hardware.eesave = yes          ; Preserve EEPROM when uploading using programmer
+upload_protocol = usbasp             ; Use the USBasp as programmer
+upload_flags =                       ; Select USB as upload port and divide the SPI clock by 8
+  -PUSB
+  -B8